您的位置:网站首页 > 新闻资讯 > 正文

解决氟碳油漆施工小问题

作者:奇锐涂料 来源: 日期:2017-3-31 10:45:47

  摘要:氟碳油漆依靠其强大的氟元素电负性和氟碳键能在多种领域中都受到了十分高度的应用,无论是化工、电子、机械,甚至是航空航天产业都讲又十分广泛高能的价值。可是,不正确的施工也会引起一些小问题,而影响了最终的性能效果,那么,出现这些小问题的时候该如何解决呢?

  Abstract: fluorocarbon paint, relying on its powerful fluorine elemental electronegativity and fluorocarbon bond energy in various areas have been very highly application, whether chemical, electronic, mechanical, and even the aerospace industry is the value of a wide range and high energy. However, incorrect construction can also cause a few small problems, and affect the performance of the final result, so these little problems of how to solve?

  一、氟碳油漆的正确施工步骤

  A, the fluorine carbon paint right construction steps

  1、基层处理,目的是为了让涂抹面更加平整。没有灰尘,这样才能保证氟碳喷漆的正常喷涂。

  1, basic level processing, in order to make the surface more smooth. Without dust, so as to ensure the normal order of the fluorine carbon paint spraying.

  2、刮腻子,在墙面上涂刷底料。座弹线,分格。准备喷涂的基线为喷涂做准备。

  2, blow be bored with child, besmear brushs base on metope. And two spring wire frame. The baseline for spraying preparation for spraying.

  3、拉毛,让纹路保持一致,均匀,之后就能够刷漆了。

  3, hair, let a grain is consistent, uniform, can brush paint.

  4、刷漆要配合封底漆、弹性中间漆和面漆配合使用,并且涂抹过程中要进行找平,选择适宜温度的环境,等待干燥。

  4, brush paint to cooperate seal primer, elastic intermediate paint and paint, and in the process of applying for leveling, choose suitable temperature environment, wait for dry.

  二、 氟碳油漆小问题再解决

  Second, the fluorine carbon paint small problems to solve

  1、 出现喷漆桔皮、掉粉现象的原因:最大的可能性是因为施工 粘度过高,稀释剂在挥发的过程中速度过快,喷枪空气流量大二出油量小。所以在涂刷的时候,漆膜太厚就容易出现这样的现象。

  1, a spray paint the cause of the phenomenon of orange peel, off powder, most likely because of excessive construction viscosity, thinner, in the process of volatile speed too fast, the quantity of oil spray gun air flow a sophomore. So in besmear to brush, paint film is too thick to appear this phenomenon.

  处理方法:降低施工粘度。调整稀释剂成分,尽量把握好喷枪的使用方法,改善施工温度。

  Processing method: reduce the viscosity of construction. Adjust the thinner components, try to grasp the use of the gun, improving construction temperature.

  2、 出现咬底现象的原因:底漆未干,就喷涂面漆。底漆与面漆不配套,底层漆膜承受不了面层容易出现溶胀。

  2, a bit at the bottom of phenomenon the reason: primer did not work, can spray paint. Primer and paint don't match, the underlying paint film is not prone to swelling on the surface.

  处理方法:使底涂干透之后再喷涂面漆,尽量选择配套产品,把握好重涂时间。

  Processing method: make coat dry after spraying paint again, try to choose products, grasp the good painting time.

友情链接